EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve

(1 customer review)

$70.00

The EF18LJ241 solenoid valve is a brand new Bryant Carrier OEM humidifier water solenoid valve that comes packed and sealed in a factory authorized parts bag. We have a list showing the humidifier models where this solenoid is used below in the description. Same Business Day Fast Shipping! In Stock and Ready to Ship!

1 in stock

Description

Purchase the EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve from Us and Save!

Same Business Day Fast Shipping! In Stock and Ready to Ship!

We Would Love to Have Your Business!

bryant_logocarrier_logobbbAplus

EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve in bag

EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve in bag (back view)

  • The EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve pictured below replaces many solenoid valves on many Bryant Carrier humidifiers.
  • The EF18LJ241 replaces older Bryant Carrier Humidifier Solenoid part numbers 2-02527, P901-1003, EF18LJ242.
  • The EF18LJ241 is a brand new Bryant Carrier OEM humidifier solenoid valve that comes packed and sealed in a factory authorized parts bag.
  • Please note, this is a 24 volt DC valve used on many Bryant and Carrier Humidifiers. Bryant Carrier Humidifiers have a rectifier that changes the voltage from AC to DC volts. The rectifier is located in the plug, where the plug, plugs into the solenoid valve.
  • Below we have pictures with an option for you to purchase.
  • We have instructions listed under the pictures below that tell how to replace a humidifier solenoid valve.
  • Please email us with your humidifier’s model number if you want us to find out if this is the solenoid valve your Bryant, Carrier humidifier uses. Our email address is: support@arnoldservice.com
  • We would love to help you out and have your business!

EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve Replacement Instructions:

  1. For power units unplug electrical cord. For bypass, units turn off power to furnace. Also, turn the humidistat off.
  2. Shut off the water supply at the saddle valve
  3. Disconnect inlet and outlet water compression nuts. Double wrench. Note, some water may drip on the floor. Remove the orifice (which controls the water flow) from the plastic or copper tube and make sure there is no obstruction. If blocked clean or replace.
  4. Remove the wire nuts from the water solenoid valve wire connections. Set aside.
  5. Remove screws that secure valve to unit.
  6. Attach a new valve with screws. Do not over-torque screws into plastic housing.
  7. Reconnect wires with wire nuts.
  8. For units with plastic feed tubes inspect for brittleness, hairline cracks, nicks or abrasions, etc.  Replace if necessary.
  9. I would highly recommend completing this step while the humidifier water supply line is disconnected to clean out the supply line/saddle valve and make sure that you have a good flow of water coming out of the water supply line. Many times a new valve can become stopped up if this step is not completed. This can be accomplished by taking a bucket, setting the loose humidifier water supply line down into the bucket (two people are best), then turn on the saddle valve to get all loose sediment out of the saddle valve and the waterline. This can be accomplished by allowing the water to run into the bucket for 10 to 15 seconds. If you can not get adequate water flow out of your saddle valve then you will need to replace your saddle valve. We sell a real good Supco saddle valve.
  10. Reconnect the water lines, double wrenching the compression nuts.
  11. Turn the water back on and check the system for leaks. Tighten compression nuts as necessary.
  12. Restore electrical service and activate furnace by turning up the thermostat.
  13. Turn up humidistat to verify the operation of humidifier.
  14. Recheck for leaks. Turn down humidistat to make sure the valve shuts off. Reset humidistat and thermostat to original levels.

The EF18LJ241 Humidifier Solenoid Valve is used in the Bryant Carrier Humidifier Models listed below:

Additional information

Weight1.0 lbs
Dimensions10 × 6 × 6 in

1 review for EF18LJ241 Bryant Carrier Humidifier Water Solenoid Valve

  1. Linda

    Parts Arrived today, already put them on… THANK YOU, THANK YOU!!! Needed the humidity in our house… delivery was great!! Linda

Add a review

Your email address will not be published. Required fields are marked *

You may also like…