4005 Aprilaire Water Solenoid Valve

$73.00

The 4005 Aprilaire Water Solenoid Valve is a brand new OEM genuine Aprilaire part that comes in an Aprilaire Research Products factory box. The Aprilaire Model 4005 Water Solenoid valve is the exact replacement valve for Aprilaire Humidifiers Models: 110 & 112. This Humidifier Solenoid Valve will be Shipped the Next Business Day. Order before 9 AM. Eastern Time for Same Day Shipping. 

 

1 in stock

Description

Purchase the 4005 Aprilaire Water Solenoid Valve from Us and Save!

This Humidifier Solenoid Valve will be Shipped the Next Business Day. Order before 9 AM. Eastern Time for Same Day Shipping. 

We Would Love to Have Your Business!

aprilaire logo2aprilaire20logo bbbAplus

  • The 4005 Aprilaire Water Solenoid Valve is a brand new OEM genuine Aprilaire part that comes in an Aprilaire Research Products factory box.
  • The Aprilaire Model 4005 Water Solenoid valve pictured below is the exact replacement valve for Aprilaire Humidifiers Models: 110 & 112.
  • Includes compression washer, nut and 4004 strainer on inlet side of valve.
  • *Please note, 4005 Aprilaire Water Solenoid Valve is a 120 volt valve.
  • Please email us anytime if you have a question. Our email address is: support@arnoldservice.com
  • We would love to help you out and have your business!

4005 Aprilaire Water Solenoid Valve
Solenoid Valve Replacement Instructions:

  1. For power units unplug electrical cord. For bypass units turn off power to furnace. Also turn the humidistat off.
  2. Shut off water supply at the saddle valve
  3. Disconnect inlet and outlet water compression nuts. Double wrench. Note, some water may drip on floor. Remove the orifice (which controls the water flow) from the plastic or copper tube and make sure there is no obstruction. If blocked clean or replace.
  4. Remove the wire nuts from the water solenoid valve wire connections. Set aside.
  5. Remove screws that secure valve to unit.
  6. Attach new valve with screws. Do not over-torque screws into plastic housing.
  7. Reconnect wires with wire nuts.
  8. For units with plastic feed tubes inspect for brittleness, hairline cracks, nicks or abrasions, etc. Replace if necessary.
  9. I would highly recommend completing this step while the humidifier water supply line is disconnected to clean out the supply line/saddle valve and make sure that you have a good flow of water coming out of the water supply line. Many times a new valve can become stopped up if this step is not completed. This can be accomplished by taking a bucket, setting the loose humidifier water supply line down into the bucket (two people are best), then turn on the saddle valve to get all loose sediment out of the saddle valve and the water line. This can be accomplished by allowing the water to run into the bucket for 10 to 15 seconds. If you can not get adequate water flow out of your saddle valve then you will need to replace your saddle valve. We sell a real good Supco saddle valve on the following page: Please click here for the saddle valve we recommend.
  10. Reconnect the water lines, double wrenching the compression nuts.
  11. Turn water back on and check system for leaks. Tighten compression nuts as necessary.
  12. Restore electrical service and activate furnace by turning up the thermostat.
  13. Turn up humidistat to verify operation of humidifier.
  14. Recheck for leaks. Turn down humidistat to make sure valve shuts off. Reset humidistat and thermostat to original levels.

Additional information

Weight 2.0 lbs
Dimensions 10 × 6 × 6 in

Reviews

There are no reviews yet.

Be the first to review “4005 Aprilaire Water Solenoid Valve”

Your email address will not be published. Required fields are marked *