1137-17 General Humidifier Water Solenoid Valve 120 Volts

$72.00

The 1137-17 General Humidifier Water Solenoid Valve 120 Volts Assembly is a replacement solenoid valve assembly compatible for use with the GeneralAire Legacy Humidifier Models 1137 and 1137R.

Out of stock

Description

generalairelogo1  bbbAplus

The GeneralAire 1137-17 is the correct replacement solenoid valve assembly for the following humidifier models. The 1137-17 solenoid is rated at 115 volts:

  • GeneralAire 1137
  • GeneralAire 1137R

The 1137-17 General Humidifier Water Solenoid Valve 120 Volts Assembly is a replacement solenoid valve assembly compatible for use with the GeneralAire Legacy Humidifier Models 1137 and 1137R. The 1137-17 115/120 volt solenoid valve assembly promotes the efficient flow of moisture through your Legacy humidifier. The GeneralAire 7341 solenoid valve assembly is an efficient 1137 humidifier replacement part. 1137-17 General Humidifier Water Solenoid Valve 120 Volts Assembly specifications:

  • OEM part
  • 115/120 volts
  • GFI number 7341
  • Part number 1137-17
  • Compatible with the 1137 series humidifiers
  • Please email us anytime if you have a question. Our email address is: support@arnoldservice.com
1137-17 General Humidifier Water Solenoid Valve 120 Volts
1137-17 General Humidifier Water Solenoid Valve 120 Volts

Solenoid Valve Replacement Instructions:

  1. For power units unplug electrical cord. For bypass units turn off power to furnace. Also turn the humidistat off.
  2. Shut off water supply at the saddle valve
  3. Disconnect inlet and outlet water compression nuts. Double wrench. Note, some water may drip on floor. Remove the orifice (which controls the water flow) from the plastic or copper tube and make sure there is no obstruction. If blocked clean or replace.
  4. Remove the wire nuts from the water solenoid valve wire connections. Set aside.
  5. Remove screws that secure valve to unit.
  6. Attach new valve with screws. Do not over-torque screws into plastic housing.
  7. Reconnect wires with wire nuts.
  8. For units with plastic feed tubes inspect for brittleness, hairline cracks, nicks or abrasions, etc. Replace if necessary.
  9. I would highly recommend completing this step while the humidifier water supply line is disconnected to clean out the supply line/saddle valve and make sure that you have a good flow of water coming out of the water supply line. Many times a new valve can become stopped up if this step is not completed. This can be accomplished by taking a bucket, setting the loose humidifier water supply line down into the bucket (two people are best), then turn on the saddle valve to get all loose sediment out of the saddle valve and the water line. This can be accomplished by allowing the water to run into the bucket for 10 to 15 seconds. If you can not get adequate water flow out of your saddle valve then you will need to replace your saddle valve. We sell a real good Supco saddle valve.
  10. Reconnect the water lines, double wrenching the compression nuts.
  11. Turn water back on and check system for leaks. Tighten compression nuts as necessary.
  12. Restore electrical service and activate furnace by turning up the thermostat.
  13. Turn up humidistat to verify operation of humidifier. Recheck for leaks. Turn down humidistat to make sure valve shuts off. Reset humidistat and thermostat to original levels.

Additional information

Weight2.0 lbs
Dimensions10 × 6 × 7 in

Reviews

There are no reviews yet.

Be the first to review “1137-17 General Humidifier Water Solenoid Valve 120 Volts”

Your email address will not be published. Required fields are marked *