Please Check Out Our 2009 Sale Prices!

Hello Everyone! We Hope All of You Have A Happy, Healthful & Prosperous 2009! 

Please ClicK Here if you would like to return to our furnace ignitors page.

We display these two furnace manufacturer's ignitors together because Bryant is manufactured by Carrier Corporation. Most of the Bryant & Carrier parts are the same. The LH33ZS004 is the most common type that is found in most Bryant & Carrier Furnaces" Below are pictures with an opportunity for you to purchase.

If you have a Bryant or Carrier Furnace, then we have the furnace ignitors for you!

  Be Prepared, Protect Your Family from being Uncomfortable and cold on those Cold Winter Nights.....Buy a spare furnace ignitor to have on hand. Since 1992, with the introduction of the new High efficiency furnaces, Ignitor failures on furnaces have become a major problem. I have seen it every year in my 14 year HVAC business. I do not want you to be caught out in the cold! That is why I am offering you these ignitors at wholesale prices!

These Are Wholesale Prices!

Purchase your furnace ignitors from us and Save $$$$! We ship USPS & UPS directly to your front door. 

We Would Love To Have Your Business!

Dedicated to Fair Business Practices and Customer Satisfaction.

We are members of the Better Business Bureau with an A+ Rating.

Kentucky State Masters HVAC License # M01340

  Shop With Confidence!

We are Square Trade & PayPal Verified Members!

We now have VeriSign Secure Credit Card Processing and Cool Cart Shopping Cart Service!

We Have Processed Over 7,000 Successful PayPal Orders!

 We Have Promptly Shipped Over 50,000 Orders Since 2002!

We are dedicated to helping you solve your heating & air conditioning problems!  

Problem: Your furnace will not ignite the gas to produce heat for your home. When a furnace has a bad ignitor what I see most of the time is the following sequence of operation: 

1. Thermostat calls for heat.

2. Draft inducer motor starts.

3. Pressure switch attached by a small plastic or rubber tube senses the negative pressure produced by the draft inducer and closes.

4. Draft inducer runs for 30 seconds to a minute before you hear a gas hissing sound. The ignitor did not glow, the flame sensor (a small metal probe about 1/8" in diameter, with a white porcelain base) does not sense the flame, so after 8 to 10 seconds the hissing sounds stops with no ignition of gas to heat your home. Your furnace shuts down and goes into a lock out condition until you turn your power switch back off and on again. 

Solution: Sorry, but you need to purchase and install a new ignitor.

Below we have pictures of Ignitors that many Bryant & Carrier furnaces have installed in them, with an opportunity for you to purchase.

Below is a scanned picture of various Ignitor Ceramic Block Styles & Terminal Block Styles. 

Bryant, Carrier LH33ZS004 Hot Surface Ignitor:

The Bryant, Carrier Ignitor pictured below replaces most Bryant, Carrier & Trane IGN 26 ignitors. It is Bryant Carrier Part # LH33ZS 004 & LH33ZS 003. I called my Bryant & Carrier supplier. My supplier said, "this ignitor is the most popular ignitor, and is used in 2,572 Bryant, Carrier furnaces." This Ignitor has a Norton 271M on the plug. The ignitor has a block style "C" and a terminal connector "D."  Below we have pictures of the ignitor with an opportunity for you to purchase. The ignitor comes in a well packed box with padding. Please click the "Add to Cart" button below to purchase: 

One part that you might need....I hope you do not. I thought that I would add this bracket to our site because I have bent a few of the brackets installing the ignitors in the Bryant Plus 90 and 90I furnaces. Sometimes you have to bend the ignitor bracket holder back to get the ignitor out. I have bent these before where the bracket will no longer hold the ignitor secure enough. Below is a picture of the bracket with an opportunity for you to purchase if you think you might need one. Thanks!

Bryant, Carrier LH33ZG001 Hot Surface Ignitor:

This ignitor is found on the newer Bryant Carrier furnaces. This ignitor is used in 354 Bryant Carrier Furnaces. This is a nitride ignitor and has a terminal block style letter "A". Please click here if you would like to view a PDF file that shows the furnace model numbers where this ignitor is used.  Below we have pictures with an opportunity for you to purchase.

Above ignitor out of box:         Above ignitor plug:

Bryant, Carrier 332505-751 Ignitor Kit:

This ignitor kit converts Silicon Carbide ignitors to Silicon Nitride ignitors on 40 inch tall mid efficiency Bryant, Carrier furnaces. The kit is used to upgrade ignitors on the following Bryant, Carrier models: 58PAV, 58RAV, 58WAV, 58ZAV, 58TUA, 58TMA, 58UXT, 58DXT, 58UHV, 58UXV, 58YAV, 58SSC, 58DHC, 383KAV, 373LAV, 395CAV, 376CAV, 330AAV, 331AAV, 330JAV, 331JAV, 333BAV, 333JAV, 393AAV, 480BAV, 481BAV, PG8UAA, PG8DAA, GB1AAV, and GB3AAV. The 332505-751 Ignitor kit comes with:

 (1) Silicon Nitride Igniter-Part #LH33ZG001,

(1) Igniter Mounting Bracket- Part #332285 401

(2) Mounting Screws-Part #FAW5808B

(1) Adapter Mounting Harness- Part #329130 701

(1) Installation Instructions.

Below we have pictures with an opportunity for you to purchase:

Bryant Carrier Standing Pilots:

The two pilots that we have listed below are found on many of the older Bryant & Carrier Furnaces. One type has three wires coming out of it and the other has only two wires. Sometimes the pilot becomes dirty and inoperative. The pilot senses the heat of the pilot flame, then sends a closed circuit signal back to the main gas valve saying that it is OK to open the main gas valve because there is a pilot flame present. If the pilot is dirty your furnace's main gas valve will click off and on, or may not open at all. Make sure you have a nice blue flame. If you have a yellow flame the pilot probably needs cleaning. I turn the gas and electricity off on the furnace, then take compressed air to blow the dirt out of the pilot. Most of the time this works, but sometimes you will need to remove the pilot for cleaning. Sometimes these pilots become inoperative and you will need a new one. Below we have pictures with an opportunity for you to purchase:

Below are listed Links to Other Pages where we sell other specific Furnace Ignitors:

 Uni-Line Furnace Ignitors Home Page

Amana Furnace Ignitors Page

Goodman, Janitrol Ignitors

International Comfort Products-Comfortmaker, Heil, Tempstar, Whirlpool Ignitors

Nordyne Ignitors

Rheem & Rudd Ignitors

York Ignitors

Honeywell Q3400A SmartValve Ignitor-Flame Rod Assembly

*For Your Information: When handling & installing ignitors never touch the gray glass part of the ignitor. Handle & install the ignitor using the white porcelain part of the ignitor. If you touch the gray glass, it could shorten the life of the ignitor. Ignitors are very fragile. If you drop it or hit it against something the ignitor will easily break.

Did you find what you need? Below, you may use Google to search our site or the Web:

Thanks For the Opportunity to Do Business With You!